ISO 20816-2:2017 - $138.00   BUY NOW

Mechanical vibration - Measurement and evaluation of machine vibration - Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min

ISO 20816-2:2017 Publication Description:

ISO 20816-2:2017 is applicable to land-based gas turbines, steam turbines and generators (whether coupled with gas and/or steam turbines) with power outputs greater than 40 MW, fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min. The criteria provided in ISO 20816-2:2017 can be applied to the vibration of the gas turbine, steam turbine and generator (including synchronizing clutches). ISO 20816-2:2017 establishes provisions for evaluating the severity of the following in-situ, broad-band vibration:

a) structural vibration at all main bearing housings or pedestals measured radial (i.e. transverse) to the shaft axis;

b) structural vibration at thrust bearing housings measured in the axial direction;

c) vibration of rotating shafts radial (i.e. transverse) to the shaft axis at, or close to, the main bearings.

These are in terms of the following:

- vibration under normal steady-state operating conditions;

- vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;

- changes in vibration which can occur during normal steady-state operation.

ISO 20816-2:2017 is not applicable to the following:

i) electromagnetic excited vibration with twice line frequency at the generator stator windings, core and housing;

ii) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives);

NOTE ISO 3977‑3 defines aero-derivatives as aircraft propulsion gas generators adapted to drive mechanical, electrical or marine propulsion equipment. Large differences exist between heavy-duty and aero-derivative gas turbines, for example, in casing flexibility, bearing design, rotor-to-stator mass ratio and mounting structure. Different criteria, therefore, apply for these two turbine types.

iii) steam turbines and/or generators with outputs less than or equal to 40 MW or with rated speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (although generators seldom fall into this latter category) (see ISO 7919‑3 and ISO 10816‑3);

iv) gas turbines with outputs less than or equal to 40 MW or with rated speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (see ISO 7919‑3 or ISO 7919‑4 and ISO 10816‑3 or ISO 10816‑4);

v) the evaluation of combustion vibration but does not preclude monitoring of combustion vibration.

International Classification for Standards (ICS)

ICS Classification Field ICS Field Sub-Group and Number
ICS-17-Metrology ICS Vibrations-Shock/Vibration (17.160)
ICS-27-Energy ICS Gas/Steam Turbines (27.040)
ICS-29-Electrical ICS Generating Sets (29.160.40)

ICS Related Standards

Cart Document Number Document Title
$45.00 ISO 10055:1996 Mechanical vibration - Vibration testing requirements for shipboard equipment and machinery components
$68.00 ISO 10112:1991 Damping materials - Graphical presentation of the complex modulus
$103.00 ISO/TS 10811-1:2000 Mechanical vibration and shock -- Vibration and shock in buildings with sensitive equipment -- Part 1: Measurement and evaluation
$68.00 ISO/TS 10811-2:2000 Mechanical vibration and shock -- Vibration and shock in buildings with sensitive equipment -- Part 2: Classification
$138.00 ISO 10813-1:2004 Vibration generating machines - Guidance for selection - Part 1: Equipment for environmental testing
$138.00 ISO 10815:2016 Mechanical vibration - Measurement of vibration generated internally in railway tunnels by the passage of trains
$149.00 ISO 10816-1:1995 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 1: General guidelines
$22.00 ISO 10816-1/Amd1:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 1: General guidelines - Amendment 1
$103.00 ISO 10816-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$103.00 ISO 10816-21:2015 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 21: Horizontal axis wind turbines with gearbox
$68.00 ISO 10816-3:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ
$103.00 ISO 10816-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings
$138.00 ISO 10816-5:2000 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 5: Machine sets in hydraulic power generating and pumping plants
$68.00 ISO 10816-6:1995 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 6: Reciprocating machines with power ratings above 100 kW
$19.00 ISO 10816-6:1995/Amd1:2015 - Amendment 1
$103.00 ISO 10816-7:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts
$162.00 ISO 10816-8:2014 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 8: Reciprocating compressor systems
$138.00 ISO 10817-1:1998 Rotating shaft vibration measuring systems - Part 1: Relative and absolute sensing of radial vibration
$103.00 ISO 13372:2012 Condition monitoring and diagnostics of machines - Vocabulary
$209.00 ISO 13373-1:2002 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 1: General procedures
$162.00 ISO 13373-2:2016 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 2: Processing, analysis and presentation of vibration data
$173.00 ISO 13373-2:2005 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 2: Processing, analysis and presentation of vibration data
$185.00 ISO 13373-3:2015 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 3: Guidelines for vibration diagnosis
$103.00 ISO 13374-1:2003 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 1: General guidelines
$162.00 ISO 13374-2:2007 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 2: Data processing
$138.00 ISO 13374-3:2012 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 3: Communication
$45.00 ISO 13374-4:2015 Condition monitoring and diagnostics of machine systems - Data processing, communication and presentation - Part 4: Presentation
$162.00 ISO 13379-1:2012 Condition monitoring and diagnostics of machines - Data interpretation and diagnostics techniques - Part 1: General guidelines
$68.00 ISO 13379-2:2015 Condition monitoring and diagnostics of machines - Data interpretation and diagnostics techniques - Part 2: Data-driven applications
$138.00 ISO 13381-1:2015 Condition monitoring and diagnostics of machines - Prognostics - Part 1: General guidelines
$149.00 ISO 13381-1:2004 Condition monitoring and diagnostics of machines - Prognostics - Part 1: General guidelines
$162.00 ISO 14695:2003 Industrial fans - Method of measurement of fan vibration
$185.00 ISO 14837-1:2005 Mechanical vibration - Ground-borne noise and vibration arising from rail systems - Part 1: General guidance
$209.00 ISO/TS 14837-32:2015 Mechanical vibration - Ground-borne noise and vibration arising from rail systems - Part 32: Measurement of dynamic properties of the ground
$162.00 ISO 14839-1:2002 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 1: Vocabulary
$19.00 ISO 14839-1/Amd1:2010 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 1: Vocabulary - Amendment 1
$138.00 ISO 14839-2:2004 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 2: Evaluation of vibration
$162.00 ISO 14839-3:2006 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 3: Evaluation of stability margin
$185.00 ISO 14839-4:2012 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 4: Technical guidelines
$162.00 ISO 14963:2003 Mechanical vibration and shock - Guidelines for dynamic tests and investigations on bridges and viaducts
$138.00 ISO 15230:2007 Mechanical vibration and shock - Coupling forces at the man-machine interface for hand-transmitted vibration
$103.00 ISO 15261:2004 Vibration and shock generating systems - Vocabulary
$45.00 ISO 15261:2004/Amd1:2016 - Amendment 1
$138.00 ISO 16063-1:1998 Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts
$162.00 ISO 16063-11:1999 Methods for the calibration of vibration and shock transducers -- Part 11: Primary vibration calibration by laser interferometry
$138.00 ISO 16063-12:2002 Methods for the calibration of vibration and shock transducers - Part 12: Primary vibration calibration by the reciprocity method
$138.00 ISO 16063-13:2001 Methods for the calibration of vibration and shock transducers - Part 13: Primary shock calibration using laser interferometry
$185.00 ISO 16063-15:2006 Methods for the calibration of vibration and shock transducers - Part 15: Primary angular vibration calibration by laser interferometry
$68.00 ISO 16063-16:2014 Methods for the calibration of vibration and shock transducers - Part 16: Calibration by Earths gravitation
$68.00 ISO 16063-17:2016 Methods for the calibration of vibration and shock transducers - Part 17: Primary calibration by centrifuge
$19.00 ISO 16063-1:1998/Amd1:2016 - Amendment 1
$162.00 ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers -- Part 21: Vibration calibration by comparison with a reference transducer
$19.00 ISO 16063-21:2003/Amd1:2016 - Amendment 1
$138.00 ISO 16063-22:2005 Methods for the calibration of vibration and shock transducers - Part 22: Shock calibration by comparison to a reference transducer
$19.00 ISO 16063-22:2005/Amd1:2014 - Amendment 1
$103.00 ISO 16063-31:2009 Methods for the calibration of vibration and shock transducers - Part 31: Testing of transverse vibration sensitivity
$68.00 ISO 16063-32:2016 Methods for the calibration of vibration and shock transducers - Part 32: Resonance testing - Testing the frequency and the phase response of accelerometers by means of shock excitation
$185.00 ISO 16063-41:2011 Methods for the calibration of vibration and shock transducers - Part 41: Calibration of laser vibrometers
$68.00 ISO 16063-42:2014 Methods for the calibration of vibration and shock transducers - Part 42: Calibration of seismometers with high accuracy using acceleration of gravity
$138.00 ISO 16063-43:2015 Methods for the calibration of vibration and shock transducers - Part 43: Calibration of accelerometers by model-based parameter identification
$68.00 ISO 16587:2004 Mechanical vibration and shock - Performance parameters for condition monitoring of structures
$138.00 ISO 17359:2011 Condition monitoring and diagnostics of machines - General guidelines
$103.00 ISO 18129:2015 Condition monitoring and diagnostics of machines - Approaches for performance diagnosis
$103.00 ISO 18312-1:2012 Mechanical vibration and shock - Measurement of vibration power flow from machines into connected support structures - Part 1: Direct method
$138.00 ISO 18312-2:2012 Mechanical vibration and shock - Measurement of vibration power flow from machines into connected support structures - Part 2: Indirect method
$138.00 ISO 18431-1:2005 Mechanical vibration and shock - Signal processing - Part 1: General introduction
$68.00 ISO 18431-2:2004 Mechanical vibration and shock - Signal processing - Part 2: Time domain windows for Fourier Transform analysis
$68.00 ISO 18431-3:2014 Mechanical vibration and shock - Signal processing - Part 3: Methods of time-frequency analysis
$103.00 ISO 18431-4:2007 Mechanical vibration and shock - Signal processing - Part 4: Shock-response spectrum analysis
$138.00 ISO 18434-1:2008 Condition monitoring and diagnostics of machines - Thermography - Part 1: General procedures
$68.00 ISO 18436-1:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 1: Requirements for assessment bodies and the assessment process
$185.00 ISO 18436-2:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 2: Vibration condition monitoring and diagnostics
$68.00 ISO 18436-3:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 3: Requirements for training bodies and the training process
$103.00 ISO 18436-4:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 4: Field lubricant analysis
$103.00 ISO 18436-5:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 5: Lubricant laboratory technician/analyst
$68.00 ISO 18436-6:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 6: Acoustic emission
$103.00 ISO 18436-7:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 7: Thermography
$68.00 ISO 18436-8:2013 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 8: Ultrasound
$103.00 ISO 18437-1:2012 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 1: Principles and guidelines
$103.00 ISO 18437-2:2005 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 2: Resonance method
$19.00 ISO 18437-2/Amd1:2010 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 2: Resonance method - Amendment 1
$103.00 ISO 18437-3:2005 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 3: Cantilever shear beam method
$19.00 ISO 18437-3/Amd1:2010 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 3: Cantilever shear beam method - Amendment 1
$138.00 ISO 18437-4:2008 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 4: Dynamic stiffness method
$103.00 ISO 18437-5:2011 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 5: Poisson ratio based on comparison between measurements and finite element analysis
$138.00 ISO 18649:2004 Mechanical vibration - Evaluation of measurement results from dynamic tests and investigations on bridges
$162.00 ISO/TR 19201:2013 Mechanical vibration - Methodology for selecting appropriate machinery vibration standards
$103.00 ISO 2017-1:2005 Mechanical vibration and shock - Resilient mounting systems - Part 1: Technical information to be exchanged for the application of isolation systems
$68.00 ISO 2017-2:2007 Mechanical vibration and shock - Resilient mounting systems - Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems
$68.00 ISO 2017-3:2015 Mechanical vibration and shock - Resilient mounting systems - Part 3: Technical information to be exchanged for application of vibration isolation to new buildings
$68.00 ISO 20283-5:2016 Mechanical vibration - Measurement of vibration on ships - Part 5: Guidelines for measurement, evaluation and reporting of vibration with regard to habitability on passenger and merchant ships
$185.00 ISO 2041:2009 Mechanical vibration, shock and condition monitoring - Vocabulary
$162.00 ISO 20816-1:2016 Mechanical vibration - Measurement and evaluation of machine vibration - Part 1: General guidelines
$138.00 ISO 20958:2013 Condition monitoring and diagnostics of machine systems - Electrical signature analysis of three-phase induction motors
$68.00 ISO 21289:2008 Mechanical vibration and shock - Parameters to be specified for the acquisition of vibration data
$68.00 ISO 22096:2007 Condition monitoring and diagnostics of machines - Acoustic emission
$138.00 ISO 22266-1:2009 Mechanical vibration - Torsional vibration of rotating machinery - Part 1: Land-based steam and gas turbine generator sets in excess of 50 MW
$103.00 ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery - Requirements for instruments for measuring vibration severity
$103.00 ISO 29821-1:2011 Condition monitoring and diagnostics of machines - Ultrasound - Part 1: General guidelines
$68.00 ISO 29821-2:2016 Condition monitoring and diagnostics of machines - Ultrasound - Part 2: Procedures and validation
$68.00 ISO 3046-5:2001 Reciprocating internal combustion engines - Performance - Part 5: Torsional vibrations
$45.00 ISO 4548-7:2012 Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 7: Vibration fatigue test
$185.00 ISO 4866:2010 Mechanical vibration and shock - Vibration of fixed structures - Guidelines for the measurement of vibrations and evaluation of their effects on structures
$162.00 ISO 5344:2004 Electrodynamic vibration generating systems - Performance characteristics
$19.00 ISO 5344:2004/Amd1:2016 - Amendment 1
$45.00 ISO 5347-12:1993 Methods for the calibration of vibration and shock pick-ups - Part 12: Testing of transverse shock sensitivity
$45.00 ISO 5347-13:1993 Methods for the calibration of vibration and shock pick-ups - Part 13: Testing of base strain sensitivity
$51.00 ISO 5347-14:1993 Methods for the calibration of vibration and shock pick-ups - Part 14: Resonance frequency testing of undamped accelerometers on a steel block
$45.00 ISO 5347-15:1993 Methods for the calibration of vibration and shock pick-ups - Part 15: Testing of acoustic sensitivity
$45.00 ISO 5347-16:1993 Methods for the calibration of vibration and shock pick-ups - Part 16: Testing of mounting torque sensitivity
$45.00 ISO 5347-17:1993 Methods for the calibration of vibration and shock pick-ups - Part 17: Testing of fixed temperature sensitivity
$45.00 ISO 5347-18:1993 Methods for the calibration of vibration and shock pick-ups - Part 18: Testing of transient temperature sensitivity
$45.00 ISO 5347-19:1993 Methods for the calibration of vibration and shock pick-ups - Part 19: Testing of magnetic field sensitivity
$45.00 ISO 5347-22:1997 Methods for the calibration of vibration and shock pick-ups - Part 22: Accelerometer resonance testing - General methods
$58.00 ISO 5347-5:1993 Methods for the calibration of vibration and shock pick-ups - Part 5: Calibration by Earths gravitation'
$51.00 ISO 5347-7:1993 Methods for the calibration of vibration and shock pick-ups - Part 7: Primary calibration by centrifuge
$45.00 ISO 5347-8:1993 Methods for the calibration of vibration and shock pick-ups - Part 8: Primary calibration by dual centrifuge
$68.00 ISO 5348:1998 Mechanical vibration and shock - Mechanical mounting of accelerometers
$68.00 ISO 6070:1981 Auxiliary tables for vibration generators - Methods of describing equipment characteristics
$88.00 ISO 6954:2000 Mechanical vibration -- Guidelines for the measurement, reporting and evaluation of vibration with regard to habitability on passenger and merchant ships
$162.00 ISO 7626-1:2011 Mechanical vibration and shock - Experimental determination of mechanical mobility - Part 1: Basic terms and definitions, and transducer specifications
$173.00 ISO 7626-1:1986 Vibration and shock -- Experimental determination of mechanical mobility -- Part 1: Basic definitions and transducers
$138.00 ISO 7626-2:2015 Mechanical vibration and shock - Experimental determination of mechanical mobility - Part 2: Measurements using single-point translation excitation with an attached vibration exciter
$149.00 ISO 7626-2:1990 Vibration and shock -- Experimental determination of mechanical mobility -- Part 2: Measurements using single-point translation excitation with an attached vibration exciter
$138.00 ISO 7626-5:1994 Vibration and shock -- Experimental determination of mechanical mobility -- Part 5: Measurements using impact excitation with an exciter which is not attached to the structure
$123.00 ISO 7919-1:1996 Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Part 1: General guidelines
$68.00 ISO 7919-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$68.00 ISO 7919-3:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3: Coupled industrial machines
$103.00 ISO 7919-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 4: Gas turbine sets with fluid-film bearings
$103.00 ISO 7919-5:2005 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 5: Machine sets in hydraulic power generating and pumping plants
$68.00 ISO 8002:1986 Mechanical vibrations - Land vehicles - Method for reporting measured data
$45.00 ISO 8042:1988 Shock and vibration measurements - Characteristics to be specified for seismic pick-ups
$103.00 ISO 8528-9:1995 Reciprocating internal combustion engine driven alternating current generating sets -- Part 9: Measurement and evaluation of mechanical vibrations
$138.00 ISO 8568:2007 Mechanical shock - Testing machines - Characteristics and performance
$173.00 ISO 8568:1989 Mechanical shock - Testing machines - Characteristics and performance
$123.00 ISO 8579-2:1993 Acceptance code for gears - Part 2: Determination of mechanical vibrations of gear units during acceptance testing
$185.00 ISO 8608:2016 Mechanical vibration - Road surface profiles - Reporting of measured data
$173.00 ISO 8608:1995 Mechanical vibration - Road surface profiles - Reporting of measured data
$185.00 ISO 8626:1989 Servo-hydraulic test equipment for generating vibration - Method of describing characteristics
$19.00 ISO 8626:1989/Amd1:2016 - Amendment 1
$45.00 ISO 9688:1990 Mechanical vibration and shock - Analytical methods of assessing shock resistance of mechanical systems - Information exchange between suppliers and users of analyses
$136.00 JIS B 0906:1998 Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- General guidelines
$107.00 JIS B 0910:1999 Mechanical vibration of non-reciprocating machines -- Measurements on rotating shafts and evaluation criteria -- General guidelines
$78.00 JIS B 0912-1:2009 Condition monitoring and diagnostics of machines -- Requirements for training and certification of personnel -- Part 1: Requirements for certifying bodies and the certification process
$87.00 JIS B 0912-2:2009 Condition monitoring and diagnostics of machines -- Requirements for training and certification of personnel -- Part 2: Vibration condition monitoring and diagnostics
$107.00 JIS B 1754:1998 Acceptance code for gears -- Part 2: Determination of mechanical vibrations of gear units during acceptance testing
$107.00 JIS B 7760-1:2004 Whole-body vibration -- Part 1: Measuring instrumentation
$19.00 ISO 10816-3:2009/Amd1:2017 - Amendment 1
$19.00 ISO 10816-4:2009/Amd1:2017 - Amendment 1
$138.00 ISO 13373-7:2017 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 7: Diagnostic techniques for machine sets in hydraulic power generating and pump-storage plants
$103.00 ISO 16063-45:2017 Methods for the calibration of vibration and shock transducers - Part 45: In-situ calibration of transducers with built in calibration coil
$68.00 ISO/TR 19664:2017 Human response to vibration - Guidance and terminology for instrumentation and equipment for the assessment of daily vibration exposure at the workplace according to the requirements of health and safety
$19.00 ISO 7919-3:2009/Amd1:2017 - Amendment 1
$19.00 ISO 7919-4:2009/Amd1:2017 - Amendment 1
$68.00 ISO 8528-9:2017 Reciprocating internal combustion engine driven alternating current generating sets - Part 9: Measurement and evaluation of mechanical vibrations
$138.00 ISO 13373-9:2017 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 9: Diagnostic techniques for electric motors
$103.00 ISO 16063-33:2017 Methods for the calibration of vibration and shock transducers - Part 33: Testing of magnetic field sensitivity
$232.00 ISO 10437:2003 Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications
$138.00 ISO 10494:1993 Gas turbines and gas turbine sets - Measurement of emitted airborne noise - Engineering/survey method
$103.00 ISO 10816-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$103.00 ISO 10816-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings
$162.00 ISO 11042-1:1996 Gas turbines - Exhaust gas emission - Part 1: Measurement and evaluation
$103.00 ISO 11042-2:1996 Gas turbines - Exhaust gas emission - Part 2: Automated emission monitoring
$209.00 ISO 11086:1996 Gas turbines - Vocabulary
$240.00 ISO 14661:2000 Thermal turbines for industrial applications (steam turbines, gas expansion turbines) -- General requirements
$240.00 ISO 14661/Amd1:2002 Thermal turbines for industrial applications (steam turbines, gas expansion turbines) - General requirements - Amendment 1: Data sheets for thermal turbines for industrial applications
$232.00 ISO 19372:2015 Microturbines applications - Safety
$232.00 ISO 19859:2016 Gas turbine applications - Requirements for power generation
$162.00 ISO 19860:2005 Gas turbines - Data acquisition and trend monitoring system requirements for gas turbine installations
$232.00 ISO 21789:2009 Gas turbine applications - Safety
$232.00 ISO 2314:2009 Gas turbines - Acceptance tests
$162.00 ISO 26382:2010 Cogeneration systems - Technical declarations for planning, evaluation and procurement
$103.00 ISO 3977-1:1997 Gas turbines - Procurement - Part 1: General introduction and definitions
$45.00 ISO 3977-2:1997 Gas turbines - Procurement - Part 2: Standard reference conditions and ratings
$209.00 ISO 3977-3:2004 Gas turbines - Procurement - Part 3: Design requirements
$103.00 ISO 3977-4:2002 Gas turbines - Procurement - Part 4: Fuels and environment
$45.00 ISO 3977-5:2001 Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries
$103.00 ISO 3977-7:2002 Gas turbines - Procurement - Part 7: Technical information
$68.00 ISO 3977-8:2002 Gas turbines - Procurement - Part 8: Inspection, testing, installation and commissioning
$138.00 ISO 3977-9:1999 Gas turbines -- Procurement -- Part 9: Reliability, availability, maintainability and safety
$68.00 ISO 7919-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$103.00 ISO 7919-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 4: Gas turbine sets with fluid-film bearings
$19.00 ISO 10816-4:2009/Amd1:2017 - Amendment 1
$19.00 ISO 7919-4:2009/Amd1:2017 - Amendment 1
$209.00 ISO 18888:2017 Gas turbine combined cycle power plants - Thermal performance tests
$103.00 ISO 10816-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$138.00 ISO 22266-1:2009 Mechanical vibration - Torsional vibration of rotating machinery - Part 1: Land-based steam and gas turbine generator sets in excess of 50 MW
$68.00 ISO 7919-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$103.00 ISO 7919-5:2005 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 5: Machine sets in hydraulic power generating and pumping plants
$103.00 ISO 8528-1:2005 Reciprocating internal combustion engine driven alternating current generating sets - Part 1: Application, ratings and performance
$103.00 ISO 8528-10:1998 Reciprocating internal combustion engine driven alternating current generating sets - Part 10: Measurement of airborne noise by the enveloping surface method
$68.00 ISO 8528-12:1997 Reciprocating internal combustion engine driven alternating current generating sets - Part 12: Emergency power supply to safety services
$185.00 ISO 8528-13:2016 Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety
$68.00 ISO 8528-2:2005 Reciprocating internal combustion engine driven alternating current generating sets - Part 2: Engines
$103.00 ISO 8528-3:2005 Reciprocating internal combustion engine driven alternating current generating sets - Part 3: Alternating current generators for generating sets
$103.00 ISO 8528-4:2005 Reciprocating internal combustion engine driven alternating current generating sets - Part 4: Controlgear and switchgear
$185.00 ISO 8528-5:2013 Reciprocating internal combustion engine driven alternating current generating sets - Part 5: Generating sets
$103.00 ISO 8528-6:2005 Reciprocating internal combustion engine driven alternating current generating sets - Part 6: Test methods
$103.00 ISO 8528-7:1994 Reciprocating internal combustion engine driven alternating current generating sets -- Part 7: Technical declarations for specification and design
$68.00 ISO 8528-8:2016 Reciprocating internal combustion engine driven alternating current generating sets - Part 8: Requirements and tests for low-power generating sets
$123.00 ISO 8528-8:1995 Reciprocating internal combustion engine driven alternating current generating sets -- Part 8: Requirements and tests for low-power generating sets
$103.00 ISO 8528-9:1995 Reciprocating internal combustion engine driven alternating current generating sets -- Part 9: Measurement and evaluation of mechanical vibrations
$103.00 ISO 8528-7:2017 Reciprocating internal combustion engine driven alternating current generating sets - Part 7: Technical declarations for specification and design
$68.00 ISO 8528-9:2017 Reciprocating internal combustion engine driven alternating current generating sets - Part 9: Measurement and evaluation of mechanical vibrations