ISO 19879:2010 - $138.00   BUY NOW

Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections

ISO 19879:2010 Publication Description:

ISO 19879:2010 specifies uniform methods for the testing and performance evaluation of metallic tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. ISO 19879:2010 does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 7241-2.

Tests outlined in ISO 19879:2010 are independent of each other and document the method to follow for each test. See the appropriate component International Standard for which tests to conduct and for performance criteria.

For qualification of the connector, the minimum number of samples specified in ISO 19879:2010 is tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer and the user.

International Classification for Standards (ICS)

ICS Classification Field ICS Field Sub-Group and Number
ICS-23-Fluid ICS Flanges Couplings/Joints (23.040.60)
ICS-23-Fluid ICS Piping/Couplings (23.100.40)

ICS Related Standards

Cart Document Number Document Title
$68.00 ISO 11413:2008 Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
$68.00 ISO 11414:2009 Plastics pipes and fittings - Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
$45.00 ISO 13783:1997 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure
$45.00 ISO 13846:2000 Plastics piping systems -- End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping -- Test method for long-term leaktightness under internal water pressure
$45.00 ISO 13953:2001 Polyethylene (PE) pipes and fittings - Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
$45.00 ISO 13954:1997 Plastics pipes and fittings - Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
$45.00 ISO 13955:1997 Plastics pipes and fittings - Crushing decohesion test for polyethylene (PE) electrofusion assemblies
$68.00 ISO 13956:2010 Plastics pipes and fittings - Decohesion test of polyethylene (PE) saddle fusion joints - Evaluation of ductility of fusion joint interface by tear test
$45.00 ISO 19892:2011 Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling
$45.00 ISO/TS 19911:2010 Plastics pipes and fittings - Format of a technical file for characterizing PE spigot end fittings
$232.00 ISO 27509:2012 Petroleum and natural gas industries - Compact flanged connections with IX seal ring
$45.00 ISO 3458:2015 Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure
$51.00 ISO 3458:1976 Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of leakproofness under internal pressure
$45.00 ISO 3459:2015 Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under negative pressure
$51.00 ISO 3459:1976 Polyethylene (PE) pressure pipes - Joints assembled with mechanical fittings - Internal under-pressure test method and requirement
$45.00 ISO 3501:2015 Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force
$51.00 ISO 3501:1976 Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of resistance to pull out
$45.00 ISO 3503:2015 Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
$51.00 ISO 3503:1976 Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of leakproofness under internal pressure when subjected to bending
$68.00 ISO 7005-1:2011 Pipe flanges - Part 1: Steel flanges for industrial and general service piping systems
$162.00 ISO 7005-2:1988 Metallic flanges - Part 2: Cast iron flanges
$138.00 ISO 7005-3:1988 Metallic flanges - Part 3 : Copper alloy and composite flanges
$68.00 ISO 8639:2016 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and proof of structural design of flexible joints
$88.00 ISO 8639:2000 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness of flexible joints
$68.00 ISO 9624:1997 Thermoplastics pipes for fluids under pressure - Mating dimensions of flange adapters and loose backing flanges
$10.00 JIS B 1217:2009/AMENDMENT 1:2012 Bolting for use with pipe flanges (Amendment 1)
$107.00 JIS B 2205:1991 Basis for calculation of pipe flanges
$15.00 JIS B 2205:1991/AMENDMENT 1:2006 Basis for calculation of pipe flanges (Amendment 1)
$68.00 JIS B 2206:1995 Basis for calculation of aluminium alloy pipe flanges
$15.00 JIS B 2206:1995/AMENDMENT 1:2006 Basis for calculation of aluminium alloy pipe flanges (Amendment 1)
$68.00 JIS B 2207:1995 Basis for calculation of aluminium alloy pipe flanges with full face gasket
$15.00 JIS B 2207:1995/AMENDMENT 1:2006 Basis for calculation of aluminium alloy pipe flanges with full face gasket (Amendment 1)
$107.00 JIS B 2220:2012 Steel pipe flanges
$87.00 JIS B 2239:2013 Cast iron pipe flanges
$78.00 JIS B 8602:2002 Pipe flanges for refrigerants
$47.00 JIS B 8602:1999 Pipe flanges for refrigerants
$45.00 ISO 10763:1994 Hydraulic fluid power - Plain-end, seamless and welded precision steel tubes - Dimensions and nominal working pressures
$68.00 ISO 11237:2010 Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
$45.00 ISO/TR 11340:1994 Rubber and rubber products - Hydraulic hose assemblies - External leakage classification for hydraulic systems
$103.00 ISO/TS 11672:2016 Connectors for fluid power and general use - Designation and nomenclature
$45.00 ISO 1179-1:2013 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports
$68.00 ISO 1179-2:2013 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
$103.00 ISO 1179-3:2007 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)
$68.00 ISO 1179-4:2007 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
$45.00 ISO 11926-1:1995 Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing - Part 1: Ports with O-ring seal in truncated housing
$68.00 ISO 11926-2:1995 Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing - Part 2: Heavy-duty (S series) stud ends
$68.00 ISO 11926-3:1995 Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing - Part 3: Light-duty (L series) stud ends
$103.00 ISO 12151-1:2010 Connections for hydraulic fluid power and general use - Hose fittings - Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
$19.00 ISO 12151-1:2010/Amd1:2017 - Amendment 1
$103.00 ISO 12151-2:2003 Connections for hydraulic fluid power and general use - Hose fittings - Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings
$68.00 ISO 12151-3:2010 Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
$68.00 ISO 12151-4:2007 Connections for hydraulic fluid power and general use - Hose fittings - Part 4: Hose fittings with ISO 6149 metric stud ends
$68.00 ISO 12151-5:2007 Connections for hydraulic fluid power and general use - Hose fittings - Part 5: Hose fittings with ISO 8434-2 37 degree flared ends
$68.00 ISO 12151-6:2009 Connections for hydraulic fluid power and general use - Hose fittings - Part 6: Hose fittings with ISO 8434-6 60 degree cone ends
$68.00 ISO 1436:2009 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
$45.00 ISO 14540:2013 Hydraulic fluid power - Dimensions and requirements for screw-to-connect quick-action couplings for use at a pressure of 72 MPa (720 bar)
$45.00 ISO 14541:2013 Hydraulic fluid power - Dimensions and requirements for screw-to-connect quick-action couplings for general purpose
$138.00 ISO 14743:2004 Pneumatic fluid power - Push-in connectors for thermoplastic tubes
$45.00 ISO 15171-1:1999 Connections for fluid power and general use -- Hydraulic couplings for diagnostic purposes -- Part 1: Coupling not for connection under pressure
$68.00 ISO 15171-2:2016 Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 x 2 end for connection under pressure
$51.00 ISO 15171-2:2000 Connections for fluid power and general use -- Hydraulic couplings for diagnostic purposes -- Part 2: Coupling with M16 x 2 end for connection under pressure
$45.00 ISO 16028:1999 Hydraulic fluid power -- Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) -- Specifications
$19.00 ISO 16028/Amd1:2006 Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications - Amendment 1
$103.00 ISO 16030:2001 Pneumatic fluid power - Connections - Ports and stud ends
$19.00 ISO 16030/Amd1:2005 Pneumatic fluid power - Connections - Ports and stud ends - Amendment 1
$103.00 ISO 23297:2008 Thermoplastics hoses and hose assemblies - Wire or synthetic yarn reinforced single-pressure types for hydraulic applications - Specification
$68.00 ISO 23309:2007 Hydraulic fluid power systems - Assembled systems - Methods of cleaning lines by flushing
$103.00 ISO 3862:2009 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification
$103.00 ISO 3949:2009 Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification
$68.00 ISO 4079:2015 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification
$123.00 ISO 4079:2009 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification
$123.00 ISO 4079:2009 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification
$45.00 ISO 4397:2011 Fluid power connectors and associated components - Nominal outside diameters of tubes and nominal hose sizes
$45.00 ISO 4399:1995 Fluid power systems and components - Connectors and associated components - Nominal pressures
$45.00 ISO 6149-1:2006 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal
$68.00 ISO 6149-2:2006 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends
$68.00 ISO 6149-3:2006 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends
$68.00 ISO 6149-4:2006 Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
$103.00 ISO 6150:1988 Pneumatic fluid power - Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 Mpa, and 2,5 MPa) - Plug connecting dimensions, specifications, application guidelines and testing
$138.00 ISO 6162-1:2012 Hydraulic fluid power - Flange connections with split or one-piece flange clamps and metric or inch screws - Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
$138.00 ISO 6162-2:2012 Hydraulic fluid power - Flange connections with split or one-piece flange clamps and metric or inch screws - Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
$68.00 ISO 6164:1994 Hydraulic fluid power - Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
$68.00 ISO 6605:2002 Hydraulic fluid power - Hoses and hose assemblies - Test methods
$68.00 ISO 7241:2014 Hydraulic fluid power - Dimensions and requirements of quick-action couplings
$66.00 ISO 7241-1:1987 Hydraulic fluid power - Quick-action couplings - Part 1 : Dimensions and requirements
$138.00 ISO 7241-2:2000 Hydraulic fluid power - Quick-action couplings - Part 2: Test methods
$185.00 ISO 8434-1:2007 Metallic tube connections for fluid power and general use - Part 1: 24 degree cone connectors
$185.00 ISO 8434-2:2007 Metallic tube connections for fluid power and general use - Part 2: 37 degree flared connectors
$209.00 ISO 8434-3:2005 Metallic tube connections for fluid power and general use - Part 3: O-ring face seal connectors
$185.00 ISO 8434-6:2009 Metallic tube connections for fluid power and general use - Part 6: 60 degree cone connectors with or without O-ring
$45.00 ISO 9974-1:1996 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports
$68.00 ISO 9974-2:1996 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E)
$68.00 ISO 9974-3:1996 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B)
$68.00 ISO 9974-4:2016 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
$88.00 ISO 9974-4:2006 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
$103.00 ISO 4079:2017 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification
$103.00 ISO 1436:2017 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
$103.00 ISO 3862:2017 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification
$68.00 ISO 6149-4:2017 Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs
$68.00 ISO 6605:2017 Hydraulic fluid power - Test methods for hoses and hose assemblies
$68.00 ISO 11237:2017 Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification