ISO 16063-15:2006 - $185.00   BUY NOW

Methods for the calibration of vibration and shock transducers - Part 15: Primary angular vibration calibration by laser interferometry

ISO 16063-15:2006 Publication Description:

ISO 16063-15:2006 specifies the instrumentation and procedures used for primary angular vibration calibration of angular transducers, i.e. angular accelerometers, angular velocity transducers and rotational angle transducers (with or without amplifier) to obtain the magnitude and the phase shift of the complex sensitivity by steady-state sinusoidal vibration and laser interferometry. The methods specified in ISO 16063-15:2006 are applicable to measuring instruments (rotational laser vibrometers in particular) and to angular transducers as defined in ISO 2041 for the quantities of rotational angle, angular velocity and angular acceleration.

ISO 16063-15:2006 is applicable to a frequency range from 1 Hz to 1,6 kHz and a dynamic range (amplitude) from 0,1 rad/s2 to 1 000 rad/s2 (frequency-dependent). Calibration frequencies lower than 1 Hz (e.g. 0,4 Hz, which is a reference frequency used in other International Standards) and angular acceleration amplitudes smaller than 0,1 rad/s2 can be achieved using method 3A or method 3B specified in ISO 16063-15:2006, in conjunction with an appropriate low-frequency angular vibration generator.

ISO 16063-15:2006 describes six methods. Method 1A ( fringe-counting, interferometer type A) and method 1B ( fringe-counting, interferometer type B) are applicable to the calibration of the magnitude of complex sensitivity in the frequency range of 1 Hz to 800 Hz and under special conditions, at higher frequencies. Method 2A (minimum-point method, interferometer type A) and method 2B (minimum-point method, interferometer type B) can be used for sensitivity magnitude calibration in the frequency range of 800 Hz to 1,6 kHz. Method 3A (sine-approximation method, interferometer type A) and method 3B (sine-approximation method, interferometer type B) can be used for magnitude of sensitivity and phase calibration in the frequency range of 1 Hz to 1,6 kHz. Methods 1A, 1B and 3A, 3B provide for calibrations at fixed angular acceleration amplitudes at various frequencies. Methods 2A and 2B require calibrations at fixed rotational angle amplitudes (angular velocity amplitude and angular acceleration amplitude vary with frequency).

International Classification for Standards (ICS)

ICS Classification Field ICS Field Sub-Group and Number
ICS-17-Metrology ICS Vibrations-Shock/Vibration (17.160)

ICS Related Standards

Cart Document Number Document Title
$45.00 ISO 10055:1996 Mechanical vibration - Vibration testing requirements for shipboard equipment and machinery components
$68.00 ISO 10112:1991 Damping materials - Graphical presentation of the complex modulus
$103.00 ISO/TS 10811-1:2000 Mechanical vibration and shock -- Vibration and shock in buildings with sensitive equipment -- Part 1: Measurement and evaluation
$68.00 ISO/TS 10811-2:2000 Mechanical vibration and shock -- Vibration and shock in buildings with sensitive equipment -- Part 2: Classification
$138.00 ISO 10813-1:2004 Vibration generating machines - Guidance for selection - Part 1: Equipment for environmental testing
$138.00 ISO 10815:2016 Mechanical vibration - Measurement of vibration generated internally in railway tunnels by the passage of trains
$149.00 ISO 10816-1:1995 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 1: General guidelines
$22.00 ISO 10816-1/Amd1:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 1: General guidelines - Amendment 1
$103.00 ISO 10816-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$103.00 ISO 10816-21:2015 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 21: Horizontal axis wind turbines with gearbox
$68.00 ISO 10816-3:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ
$103.00 ISO 10816-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings
$138.00 ISO 10816-5:2000 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 5: Machine sets in hydraulic power generating and pumping plants
$68.00 ISO 10816-6:1995 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 6: Reciprocating machines with power ratings above 100 kW
$19.00 ISO 10816-6:1995/Amd1:2015 - Amendment 1
$103.00 ISO 10816-7:2009 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts
$162.00 ISO 10816-8:2014 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 8: Reciprocating compressor systems
$138.00 ISO 10817-1:1998 Rotating shaft vibration measuring systems - Part 1: Relative and absolute sensing of radial vibration
$103.00 ISO 13372:2012 Condition monitoring and diagnostics of machines - Vocabulary
$209.00 ISO 13373-1:2002 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 1: General procedures
$162.00 ISO 13373-2:2016 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 2: Processing, analysis and presentation of vibration data
$173.00 ISO 13373-2:2005 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 2: Processing, analysis and presentation of vibration data
$185.00 ISO 13373-3:2015 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 3: Guidelines for vibration diagnosis
$103.00 ISO 13374-1:2003 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 1: General guidelines
$162.00 ISO 13374-2:2007 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 2: Data processing
$138.00 ISO 13374-3:2012 Condition monitoring and diagnostics of machines - Data processing, communication and presentation - Part 3: Communication
$45.00 ISO 13374-4:2015 Condition monitoring and diagnostics of machine systems - Data processing, communication and presentation - Part 4: Presentation
$162.00 ISO 13379-1:2012 Condition monitoring and diagnostics of machines - Data interpretation and diagnostics techniques - Part 1: General guidelines
$68.00 ISO 13379-2:2015 Condition monitoring and diagnostics of machines - Data interpretation and diagnostics techniques - Part 2: Data-driven applications
$138.00 ISO 13381-1:2015 Condition monitoring and diagnostics of machines - Prognostics - Part 1: General guidelines
$149.00 ISO 13381-1:2004 Condition monitoring and diagnostics of machines - Prognostics - Part 1: General guidelines
$162.00 ISO 14695:2003 Industrial fans - Method of measurement of fan vibration
$185.00 ISO 14837-1:2005 Mechanical vibration - Ground-borne noise and vibration arising from rail systems - Part 1: General guidance
$209.00 ISO/TS 14837-32:2015 Mechanical vibration - Ground-borne noise and vibration arising from rail systems - Part 32: Measurement of dynamic properties of the ground
$162.00 ISO 14839-1:2002 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 1: Vocabulary
$19.00 ISO 14839-1/Amd1:2010 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 1: Vocabulary - Amendment 1
$138.00 ISO 14839-2:2004 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 2: Evaluation of vibration
$162.00 ISO 14839-3:2006 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 3: Evaluation of stability margin
$185.00 ISO 14839-4:2012 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings - Part 4: Technical guidelines
$162.00 ISO 14963:2003 Mechanical vibration and shock - Guidelines for dynamic tests and investigations on bridges and viaducts
$138.00 ISO 15230:2007 Mechanical vibration and shock - Coupling forces at the man-machine interface for hand-transmitted vibration
$103.00 ISO 15261:2004 Vibration and shock generating systems - Vocabulary
$45.00 ISO 15261:2004/Amd1:2016 - Amendment 1
$138.00 ISO 16063-1:1998 Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts
$162.00 ISO 16063-11:1999 Methods for the calibration of vibration and shock transducers -- Part 11: Primary vibration calibration by laser interferometry
$138.00 ISO 16063-12:2002 Methods for the calibration of vibration and shock transducers - Part 12: Primary vibration calibration by the reciprocity method
$138.00 ISO 16063-13:2001 Methods for the calibration of vibration and shock transducers - Part 13: Primary shock calibration using laser interferometry
$68.00 ISO 16063-16:2014 Methods for the calibration of vibration and shock transducers - Part 16: Calibration by Earths gravitation
$68.00 ISO 16063-17:2016 Methods for the calibration of vibration and shock transducers - Part 17: Primary calibration by centrifuge
$19.00 ISO 16063-1:1998/Amd1:2016 - Amendment 1
$162.00 ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers -- Part 21: Vibration calibration by comparison with a reference transducer
$19.00 ISO 16063-21:2003/Amd1:2016 - Amendment 1
$138.00 ISO 16063-22:2005 Methods for the calibration of vibration and shock transducers - Part 22: Shock calibration by comparison to a reference transducer
$19.00 ISO 16063-22:2005/Amd1:2014 - Amendment 1
$103.00 ISO 16063-31:2009 Methods for the calibration of vibration and shock transducers - Part 31: Testing of transverse vibration sensitivity
$68.00 ISO 16063-32:2016 Methods for the calibration of vibration and shock transducers - Part 32: Resonance testing - Testing the frequency and the phase response of accelerometers by means of shock excitation
$185.00 ISO 16063-41:2011 Methods for the calibration of vibration and shock transducers - Part 41: Calibration of laser vibrometers
$68.00 ISO 16063-42:2014 Methods for the calibration of vibration and shock transducers - Part 42: Calibration of seismometers with high accuracy using acceleration of gravity
$138.00 ISO 16063-43:2015 Methods for the calibration of vibration and shock transducers - Part 43: Calibration of accelerometers by model-based parameter identification
$68.00 ISO 16587:2004 Mechanical vibration and shock - Performance parameters for condition monitoring of structures
$138.00 ISO 17359:2011 Condition monitoring and diagnostics of machines - General guidelines
$103.00 ISO 18129:2015 Condition monitoring and diagnostics of machines - Approaches for performance diagnosis
$103.00 ISO 18312-1:2012 Mechanical vibration and shock - Measurement of vibration power flow from machines into connected support structures - Part 1: Direct method
$138.00 ISO 18312-2:2012 Mechanical vibration and shock - Measurement of vibration power flow from machines into connected support structures - Part 2: Indirect method
$138.00 ISO 18431-1:2005 Mechanical vibration and shock - Signal processing - Part 1: General introduction
$68.00 ISO 18431-2:2004 Mechanical vibration and shock - Signal processing - Part 2: Time domain windows for Fourier Transform analysis
$68.00 ISO 18431-3:2014 Mechanical vibration and shock - Signal processing - Part 3: Methods of time-frequency analysis
$103.00 ISO 18431-4:2007 Mechanical vibration and shock - Signal processing - Part 4: Shock-response spectrum analysis
$138.00 ISO 18434-1:2008 Condition monitoring and diagnostics of machines - Thermography - Part 1: General procedures
$68.00 ISO 18436-1:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 1: Requirements for assessment bodies and the assessment process
$185.00 ISO 18436-2:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 2: Vibration condition monitoring and diagnostics
$68.00 ISO 18436-3:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 3: Requirements for training bodies and the training process
$103.00 ISO 18436-4:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 4: Field lubricant analysis
$103.00 ISO 18436-5:2012 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 5: Lubricant laboratory technician/analyst
$68.00 ISO 18436-6:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 6: Acoustic emission
$103.00 ISO 18436-7:2014 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 7: Thermography
$68.00 ISO 18436-8:2013 Condition monitoring and diagnostics of machines - Requirements for qualification and assessment of personnel - Part 8: Ultrasound
$103.00 ISO 18437-1:2012 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 1: Principles and guidelines
$103.00 ISO 18437-2:2005 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 2: Resonance method
$19.00 ISO 18437-2/Amd1:2010 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 2: Resonance method - Amendment 1
$103.00 ISO 18437-3:2005 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 3: Cantilever shear beam method
$19.00 ISO 18437-3/Amd1:2010 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 3: Cantilever shear beam method - Amendment 1
$138.00 ISO 18437-4:2008 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 4: Dynamic stiffness method
$103.00 ISO 18437-5:2011 Mechanical vibration and shock - Characterization of the dynamic mechanical properties of visco-elastic materials - Part 5: Poisson ratio based on comparison between measurements and finite element analysis
$138.00 ISO 18649:2004 Mechanical vibration - Evaluation of measurement results from dynamic tests and investigations on bridges
$162.00 ISO/TR 19201:2013 Mechanical vibration - Methodology for selecting appropriate machinery vibration standards
$103.00 ISO 2017-1:2005 Mechanical vibration and shock - Resilient mounting systems - Part 1: Technical information to be exchanged for the application of isolation systems
$68.00 ISO 2017-2:2007 Mechanical vibration and shock - Resilient mounting systems - Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems
$68.00 ISO 2017-3:2015 Mechanical vibration and shock - Resilient mounting systems - Part 3: Technical information to be exchanged for application of vibration isolation to new buildings
$68.00 ISO 20283-5:2016 Mechanical vibration - Measurement of vibration on ships - Part 5: Guidelines for measurement, evaluation and reporting of vibration with regard to habitability on passenger and merchant ships
$185.00 ISO 2041:2009 Mechanical vibration, shock and condition monitoring - Vocabulary
$162.00 ISO 20816-1:2016 Mechanical vibration - Measurement and evaluation of machine vibration - Part 1: General guidelines
$138.00 ISO 20958:2013 Condition monitoring and diagnostics of machine systems - Electrical signature analysis of three-phase induction motors
$68.00 ISO 21289:2008 Mechanical vibration and shock - Parameters to be specified for the acquisition of vibration data
$68.00 ISO 22096:2007 Condition monitoring and diagnostics of machines - Acoustic emission
$138.00 ISO 22266-1:2009 Mechanical vibration - Torsional vibration of rotating machinery - Part 1: Land-based steam and gas turbine generator sets in excess of 50 MW
$103.00 ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery - Requirements for instruments for measuring vibration severity
$103.00 ISO 29821-1:2011 Condition monitoring and diagnostics of machines - Ultrasound - Part 1: General guidelines
$68.00 ISO 29821-2:2016 Condition monitoring and diagnostics of machines - Ultrasound - Part 2: Procedures and validation
$68.00 ISO 3046-5:2001 Reciprocating internal combustion engines - Performance - Part 5: Torsional vibrations
$45.00 ISO 4548-7:2012 Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 7: Vibration fatigue test
$185.00 ISO 4866:2010 Mechanical vibration and shock - Vibration of fixed structures - Guidelines for the measurement of vibrations and evaluation of their effects on structures
$162.00 ISO 5344:2004 Electrodynamic vibration generating systems - Performance characteristics
$19.00 ISO 5344:2004/Amd1:2016 - Amendment 1
$45.00 ISO 5347-12:1993 Methods for the calibration of vibration and shock pick-ups - Part 12: Testing of transverse shock sensitivity
$45.00 ISO 5347-13:1993 Methods for the calibration of vibration and shock pick-ups - Part 13: Testing of base strain sensitivity
$51.00 ISO 5347-14:1993 Methods for the calibration of vibration and shock pick-ups - Part 14: Resonance frequency testing of undamped accelerometers on a steel block
$45.00 ISO 5347-15:1993 Methods for the calibration of vibration and shock pick-ups - Part 15: Testing of acoustic sensitivity
$45.00 ISO 5347-16:1993 Methods for the calibration of vibration and shock pick-ups - Part 16: Testing of mounting torque sensitivity
$45.00 ISO 5347-17:1993 Methods for the calibration of vibration and shock pick-ups - Part 17: Testing of fixed temperature sensitivity
$45.00 ISO 5347-18:1993 Methods for the calibration of vibration and shock pick-ups - Part 18: Testing of transient temperature sensitivity
$45.00 ISO 5347-19:1993 Methods for the calibration of vibration and shock pick-ups - Part 19: Testing of magnetic field sensitivity
$45.00 ISO 5347-22:1997 Methods for the calibration of vibration and shock pick-ups - Part 22: Accelerometer resonance testing - General methods
$58.00 ISO 5347-5:1993 Methods for the calibration of vibration and shock pick-ups - Part 5: Calibration by Earths gravitation'
$51.00 ISO 5347-7:1993 Methods for the calibration of vibration and shock pick-ups - Part 7: Primary calibration by centrifuge
$45.00 ISO 5347-8:1993 Methods for the calibration of vibration and shock pick-ups - Part 8: Primary calibration by dual centrifuge
$68.00 ISO 5348:1998 Mechanical vibration and shock - Mechanical mounting of accelerometers
$68.00 ISO 6070:1981 Auxiliary tables for vibration generators - Methods of describing equipment characteristics
$88.00 ISO 6954:2000 Mechanical vibration -- Guidelines for the measurement, reporting and evaluation of vibration with regard to habitability on passenger and merchant ships
$162.00 ISO 7626-1:2011 Mechanical vibration and shock - Experimental determination of mechanical mobility - Part 1: Basic terms and definitions, and transducer specifications
$173.00 ISO 7626-1:1986 Vibration and shock -- Experimental determination of mechanical mobility -- Part 1: Basic definitions and transducers
$138.00 ISO 7626-2:2015 Mechanical vibration and shock - Experimental determination of mechanical mobility - Part 2: Measurements using single-point translation excitation with an attached vibration exciter
$149.00 ISO 7626-2:1990 Vibration and shock -- Experimental determination of mechanical mobility -- Part 2: Measurements using single-point translation excitation with an attached vibration exciter
$138.00 ISO 7626-5:1994 Vibration and shock -- Experimental determination of mechanical mobility -- Part 5: Measurements using impact excitation with an exciter which is not attached to the structure
$123.00 ISO 7919-1:1996 Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Part 1: General guidelines
$68.00 ISO 7919-2:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$68.00 ISO 7919-3:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3: Coupled industrial machines
$103.00 ISO 7919-4:2009 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 4: Gas turbine sets with fluid-film bearings
$103.00 ISO 7919-5:2005 Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 5: Machine sets in hydraulic power generating and pumping plants
$68.00 ISO 8002:1986 Mechanical vibrations - Land vehicles - Method for reporting measured data
$45.00 ISO 8042:1988 Shock and vibration measurements - Characteristics to be specified for seismic pick-ups
$103.00 ISO 8528-9:1995 Reciprocating internal combustion engine driven alternating current generating sets -- Part 9: Measurement and evaluation of mechanical vibrations
$138.00 ISO 8568:2007 Mechanical shock - Testing machines - Characteristics and performance
$173.00 ISO 8568:1989 Mechanical shock - Testing machines - Characteristics and performance
$123.00 ISO 8579-2:1993 Acceptance code for gears - Part 2: Determination of mechanical vibrations of gear units during acceptance testing
$185.00 ISO 8608:2016 Mechanical vibration - Road surface profiles - Reporting of measured data
$173.00 ISO 8608:1995 Mechanical vibration - Road surface profiles - Reporting of measured data
$185.00 ISO 8626:1989 Servo-hydraulic test equipment for generating vibration - Method of describing characteristics
$19.00 ISO 8626:1989/Amd1:2016 - Amendment 1
$45.00 ISO 9688:1990 Mechanical vibration and shock - Analytical methods of assessing shock resistance of mechanical systems - Information exchange between suppliers and users of analyses
$136.00 JIS B 0906:1998 Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- General guidelines
$107.00 JIS B 0910:1999 Mechanical vibration of non-reciprocating machines -- Measurements on rotating shafts and evaluation criteria -- General guidelines
$78.00 JIS B 0912-1:2009 Condition monitoring and diagnostics of machines -- Requirements for training and certification of personnel -- Part 1: Requirements for certifying bodies and the certification process
$87.00 JIS B 0912-2:2009 Condition monitoring and diagnostics of machines -- Requirements for training and certification of personnel -- Part 2: Vibration condition monitoring and diagnostics
$107.00 JIS B 1754:1998 Acceptance code for gears -- Part 2: Determination of mechanical vibrations of gear units during acceptance testing
$107.00 JIS B 7760-1:2004 Whole-body vibration -- Part 1: Measuring instrumentation
$19.00 ISO 10816-3:2009/Amd1:2017 - Amendment 1
$19.00 ISO 10816-4:2009/Amd1:2017 - Amendment 1
$138.00 ISO 13373-7:2017 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 7: Diagnostic techniques for machine sets in hydraulic power generating and pump-storage plants
$103.00 ISO 16063-45:2017 Methods for the calibration of vibration and shock transducers - Part 45: In-situ calibration of transducers with built in calibration coil
$68.00 ISO/TR 19664:2017 Human response to vibration - Guidance and terminology for instrumentation and equipment for the assessment of daily vibration exposure at the workplace according to the requirements of health and safety
$138.00 ISO 20816-2:2017 Mechanical vibration - Measurement and evaluation of machine vibration - Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
$19.00 ISO 7919-3:2009/Amd1:2017 - Amendment 1
$19.00 ISO 7919-4:2009/Amd1:2017 - Amendment 1
$68.00 ISO 8528-9:2017 Reciprocating internal combustion engine driven alternating current generating sets - Part 9: Measurement and evaluation of mechanical vibrations
$138.00 ISO 13373-9:2017 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 9: Diagnostic techniques for electric motors
$103.00 ISO 16063-33:2017 Methods for the calibration of vibration and shock transducers - Part 33: Testing of magnetic field sensitivity